AIGOODS Industry Knowledge Channel, sharing the product characteristics, application scenarios, and material selection techniques of new wall decoration materials such as flexible stone, PU stone leather, wood veneer board, and artificial stone paint.
Title based on real procurement and design issues
Provide a direct answer at the beginning of each article
For designers, contractors, and engineering procurement
Continuous release · Can be searched by scene tags on the image
05 Selection Framework: What to judge first, what to do next
Most of the rework in wall material selection does not come from 'the color is wrong', but from asking the wrong question at the beginning. Follow the following four steps to prevent 80% of the rework in advance.
Sequence
First judgment what
How to judge
The conclusion points
① Base layer
Strength, flatness, moisture content
Tap to check for hollow areas, use a 2m straightedge to check flatness, and first measure the moisture content of walls with high humidity
Lightweight walls/old walls/insulated walls → only lightweight adhesive materials can be selected; if the substrate is unqualified, treat it first—changing materials won't help either
② Shape
Is there any curved, cylindrical, or irregular corner?
Check the drawings and site; measure the minimum arc radius
→ Must be bendable material with curved surface, hard materials can only be spliced in small pieces, with dense diagonal seams
③ Part
Indoor / semi-outdoor / outdoor, dry area / wet area
Compare the dry-wet partitioning diagram and the external wall range
Outdoor weatherproof adhesive and waterproof edging are required; the material in the wet area must not absorb water
④ Perception
color number, texture direction, jointing method
View the physical samples under the actual lighting of the project
Both screens and exhibition halls can be deceptive; it is necessary to make color decisions after comparing on-site.
One-line mnemonic:The substrate determines whether it can be done, the modeling determines what to do, the location determines how to do it, and the perception determines what it will look like - the order cannot be reversed.
Four types of wall comparison: What are the differences in materials on the same wall?
The following table compares four types of commonly used materials under the same criteria. The values in the table are common ranges, used to judge the applicable boundaries, and do not constitute a ranking of any material.
Comparison item
Flexible Stone (Soft Stone)
PU Stone Skin Panel
Wood veneer wallboard (bamboo charcoal wood)
WPC lattice board
thickness / section
2.3–9 mm
Molded molding, divided into large plate / small plate by color
5 mm / 8 mm
List by model, such as 131×10.6 mm.
per square meter weight
About 3-7 kg/square meter
Lightweight, polyurethane foam structure
About 3.8 / 6.0 kg/square meter
The weight of the profile, hollow is lighter
Curved surface and column
Can be curved within a certain radius, covering the entire surface
Mainly in solid block molding, using matching corner pieces
Flat panel installation is the main, curved surfaces are transitioned with closing parts
The direction of the profile is fixed, and short sections are used for splicing in arcs
Construction method
No skeleton required, full adhesion after leveling the base
Full adhesion or clip, masonry walls can be directly pasted.
Paste with no-screw adhesive or snap-together.
Clip or nail fixed, can be installed in one piece
Moisture-proof performance
Does not absorb water, does not swell.
Non-porous, non-absorbent
Solid extrusion of materials, not absorb water and deform
Wood-plastic composite, not deformed by moisture
Main Applicable Areas
Interior and exterior walls, columns, ceiling
Door heads, exterior walls, feature walls, old wall renovation
Indoor wall, cabinet and door wall integrated
Background wall, column wrapping, ceiling, and screen
Points to note
Not recommended for ground installation.
The convex surface needs to avoid fixed parts
Not recommended for outdoor use
Not recommended to bend horizontally.
Common judgment misconceptions: These four sentences are most likely to mislead people
Common statements
Where is the problem
The correct method
「The more the stone texture resembles the real stone, the better」
Looking similar from a distance does not mean it looks similar up close; seams and batch differences are where problems most easily arise on site
First confirm the layout and joint relationship, then look at the texture; same project, same batch order enough.
Lightness is a result of structural choice, not a quality indicator; low self-weight is precisely the prerequisite for use on lightweight walls
Check the base material structure and inspection report, not the absolute value of weight
「Having an inspection report can meet the fire safety standard」
The report corresponds to specific models and samples, not the entire series
Compare the names of the samples in the report with the selected models item by item
「First determine the color, then calculate the amount」
Once the color is set, the layout is set, and only then can waste be calculated accurately; doing it the other way around leads to repeated re-measurement
Layout diagram → jointing scheme → consumption → material preparation, follow this sequence.
Find guidelines by space (30 articles)
Problems faced by the same space type are highly similar. Enter the corresponding group directly according to your project type, which is faster than flipping from the latest one downwards.
Procurement, construction, and acceptance are three separate activities, and problems arise differently in each. This group is arranged by "what to do when," and each article corresponds to a delivered project; the figures can be checked item by item on the case pages.
Thickness measurement of travertine sample: comparison of three groups of picture readings
The figure shows the digital caliper measurement results of three groups of flexible stone travertine samples. From left to right in the picture, the display reading of the IGOODS sample is 2.50 mm, the Hebei sample is 1.95 mm, and the Linyi sample is 1.89 mm. The table only records the readings visible in the photo, without filling in the second measurement point or thickness range not displayed.
Picture location
travertine sample
Picture shows reading
On the left
IGOODS travertine sample
2.50 mm
middle
Same category travertine samples (Hebei)
1.95 mm
Right
Same category travertine samples (Linyi)
1.89 mm
Figure 1 · Reading of thickness of travertine sample: Left IGOODS 2.50 mm, middle Hebei sample 1.95 mm, right Linyi sample 1.89 mm.Figure 2 · IGOODS travertine sample close-up, the caliper shows 2.50 mm, consistent with the reading on the left side of Figure 1.
Data range:The data shown in the photo is the displayed reading of the travertine sample at the corresponding measurement location, which does not represent the thickness range of the entire plate, multiple batches, or all products from the same origin; the second measurement point record is not displayed on this page. The decimal places displayed on the caliper are not the same as the measured accuracy confirmed by the calibration, and the single-point reading cannot be used to determine the overall quality of products from other brands or origins.
How is thickness reading used for material selection
The thickness should be checked together with the nominal specifications, agreed tolerances, and measurement methods of the selected travertine model. The 2.50 mm, 1.95 mm, and 1.89 mm in the figure can only be used to compare the current readings of these three groups of samples and cannot be judged solely on the basis of thickness for impact resistance, weather resistance, fire resistance, weight, price, or indoor and outdoor suitability.
Firstly, check the model and specifications:Define the series, texture, backing, nominal thickness, and allowable deviation of travertine, and avoid directly comparing products of different structures with the same caliber.
Recheck the project conditions:Combined with base layer, curvature radius, adhesive system and material selection for application location; performance judgment should be based on the corresponding model specifications and test reports.
Supplement measurements when intervals are needed:Record readings of multiple positions and multiple samples according to the agreed method, then summarize the range; do not use the single-point value of a photo as the upper and lower limits of product thickness.
How to check the thickness when receiving goods
Use a suitable measuring tool:Check caliper zero position, blade cleanliness and contact status before measurement, to avoid deformation of flexible samples causing reading changes.
Uniform measurement location and diameter:Clarify in advance whether it includes backing, how to deal with the holes on the surface of the stone and its convex and concave, and note the location in the record to avoid the use of different measurement methods
Record multiple locations:Record the sample, batch, location and reading point by point, and keep photos; the three sets of photos on this page are not yet sufficient to establish a multi-point measurement range.
Acceptance according to procurement agreement:Compare the actual measurement records with the specifications of the specific model, the agreed tolerances, and the acceptance methods, and do not just make a qualified conclusion based on the thickness difference between the samples.
Material selection FAQ
The following are the eight most frequently asked questions in the design and procurement phases, with answers given from the perspective of engineering practice.
How to choose wall materials? Which indicator should be considered first?
First inspect the base, then the shape, and finally the appearance. The strength, flatness, and moisture content of the base material determine whether it can be directly adhered; the presence of curved walls, columns, and irregular corners determines whether rigid materials can be used; appearance and color are determined last, as they are most prone to rework and should not be repeated unnecessarily.
In what cases should flexible stone be chosen instead of tiles or natural stone?
In three cases, flexible stone should be prioritized: the subgrade is light-weight wall or old wall, without bearing conditions; there are arched walls, cylindrical or irregular corners that need to be covered in one piece; the construction period is tight, and dry construction without ridge and wet work is required. Conversely, it is not suitable for ground paving and exposed countertops.
How to distinguish the uses of flexible stone, PU stone skin and wood paneling
Flexible stone material with a stone texture and thinness, thickness mostly in the range of 2.3-6mm, self-weight about 3-7kg/㎡, suitable for expressing stone patterns on large-area walls; PU stone skin is a three-dimensional surface, imitating natural scattered stones and rock walls, suitable for door heads, exterior walls, and renovation of old walls; wooden paneling is indoor wood color and plain fabric texture, used in guest rooms, offices, and cabinet facings.
Can the arched wall and cylinder really be fully covered?
Yes, but the radius is not infinite. Large-radius arc walls can be bent and tiled in one piece, along the arc line of the seam; small radius must first take a physical sample and try to bend at the corresponding curvature, obvious rebound can be changed to narrow strip tiling - following the arc line is more neat than hard splicing small pieces.
Can the renovation of the old wall be directly pasted? Do I need to scrape the wall first?
If the original wall is firm and without hollows, it can be covered directly, and old tile surfaces can also be used. However, before construction, it is necessary to knock on the surface one by one to check, and the hollow and sandy parts should be scraped off to the solid base and repainted - this step cannot be skipped, as any material pasted on the hollow base will also bulge.
How are fire rating and environmental data confirmed?
Read the inspection report, not the promotional language. The combustion performance grade is based on the effective inspection report of the selected model (such as GB 8624-2012 classification), and the formaldehyde and VOC data correspond to specific samples. When the project has specific requirements, the sample name in the report should be compared item by item with the selected model.
What documents do I need to prepare for the export order?
The EU market usually requires CE compliance documents, RoHS and REACH test reports; other markets mostly recognize SGS or the performance and environmental protection reports of the National Inspection Center. What is actually needed should be determined according to the regulations of the destination country and customer requirements. It is recommended to provide the list all at once before placing an order.
What is the easiest thing to forget when making a quotation?
What is most likely to be overlooked is the loss and shape. The flat wall is basically sufficient for preparation by area × 1.12; the loss of the curved wall, column wrapping, door opening and large-area paving is obviously higher, and the shaped parts should be calculated separately according to the drawing. In addition, the labor cost of surface treatment and layout alignment is not included in the installation unit price.
Case-by-case Analysis · Product by Family Analysis
In addition to the above "write by question" guides, the site also has two sections covering items one by one:Case AnalysisSeparate each delivered project individually - material selection reasons, layout algorithms, construction nodes, lighting coordination, acceptance and maintenance follow-up;Product AnalysisExplain in series and color batch by group - color map, parameter specifications, construction commonality and scene adaptation, and link to the corresponding product file. Two columns refer to each other: the guide solves 'how to choose', and the analysis page answers 'which one is chosen, and how is it used.'
No. 9001, 9th Floor, Building A, No. 166 Laifeng 5th Road, Wuhou District, Chengdu, Sichuan Province, China (Laifeng Digital Innovation Center)
Can provide
20×30 cm physical sample · Specifications · Inspection report and qualification documents · Construction phase suggestions
Material scope
The size, thickness, and weight on this page are in the common range, actual values are confirmed by product specifications and orders; combustion performance and environmental grade are based on the effective test report of the selected model
Guide on how to choose, samples on which to choose
Apply for 20×30cm physical samples, and determine the final material selection after comparing with the project lighting and adjacent materials on the site, and provide specifications, inspection reports, and construction suggestions.