酒店大堂560㎡线纹洞石墙面施工案例

艾谷思IGOODS 为四川省峨眉山市一处酒店大堂项目提供线纹洞石作为墙面材料,采用满粘法直接上墙、无需龙骨基层。项目墙面概算约 560㎡,材料规格 1220×2930mm、厚度 2.5–3.5mm、单片重量约 17kg,执行 JG/T 540-2017《建筑用柔性仿石饰面材料》。

Published time:

IGOODS provided for a hotel lobby project in Emeishan City, Sichuan Province, Hotel lobby project provided by Line Texture Travertine as a wall material, applied directly to the wall with the full-adhesion method, with no need for a keel substrate. The project wall budget is about 560㎡, material specifications 1220×2930mm, thickness 2.5–3.5mm, the weight of a single piece is about 17kg; implement JG/T 540-2017 "Flexible Stone-like Facing Materials for Buildings". The application images in this case total 10 pieces.

  • 1220×2930mm Panel specifications
  • 2.5–3.5mm thickness
  • Approx. 3.2 kg/㎡ Surface weight (converted at 17kg/piece)
  • Approx. 560 ㎡ Wall area (◆budget estimate)
  • 10 pieces Application image
  • JG/T 540-2017 Implementation standards

Project file

Project item Content
Project typeHotel lobby
Application locationLobby main wall / welcome backdrop, round columns / curved column cladding, elevator hall / walkway, wall base 0–300mm
Materials usedLine Texture Travertine (Travertine series)
Material specifications1220×2930mm, thickness 2.5–3.5mm, single piece about 17kg
Construction processFull bonding method, direct wall installation after leveling, no keel required
Implementation standardsJG/T 540-2017 'Building Flexible Stone-faced Decorative Material'
Project locationEmeishan City, Sichuan Province
Wall areaApprox. 560 ㎡ (◆ budget estimate)
Actual photo record10 pieces (on-site shooting)

Regarding the scope of this page: The material specifications, performance parameters, and applicable standards in this article all come from IGOODS product documentation and can be verified item by item. ★Project experience = Common industry practices and experience range, not as a reference for national standards data; ◆Estimate = Estimated value calculated based on the industry's common scale and the scale of this case, used to judge the scale,Not an actual measured bill; actual conditions are subject to project confirmation.

1. Customer industry usage scenario: the real wall requirements of a hotel lobby

  1. Highest traffic volume; wear resistance comes first The lobby is a space with around-the-clock high-frequency traffic; luggage carts, suitcase wheels and cleaning equipment pass repeatedly, and the wall base is especially prone to impact marks. The material's scratch resistance and ease of repair are more important than attractive texture.
  2. Floor height and volume require large panel format The wall scale in the lobby is far larger than in guest rooms; fewer seams create a stronger overall effect. Insufficient panel size leads to dense seams, fragmenting the sense of scale in the large space.
  3. Lighting layering depends on a matte base The lobby lighting design (light strips, wall-washing lights, accent lighting) only works on a matte, textured substrate; high-gloss surface materials reflect light strips into streaks of light.
  4. Fireproofing and environmental protection are hard thresholds The lobby is a crowded place, so the material's combustion performance and environmental indicators must be supported by test reports, not just verbal descriptions.
  5. Mainly curved surfaces and shapes The round columns, curved partitions and arched door openings common in lobbies can only be achieved with traditional tiles by using small-format pieces with dense seams; flexible materials can be directly bent and wrapped around curves, creating continuous shapes without folded corners.
  6. Handover must be fast and must not affect the opening countdown The lobby is one of the last areas completed before opening, and the schedule is compressed the hardest; solutions that can be applied directly to the wall without framing and curing have obvious advantages.

II. Material comparison: why linear travertine

Why choose linear vein stone

The characteristics of Line Texture Travertine are layering stretched into fine, dense parallel lines, the pore feel is more regular than that of ordinary travertine. This characteristic is very practical in hotels: the clear width of guest room corridors is only about 1.5 meters, and the walls fill the field of view. Strongly pitted textures appear messy at small scales, while the linear grain is horizontal, visually elongating the depth of the corridor.

This project has a large area and diverse locations: elevator lobby, continuous arched corridor, cylindrical cladding, curved walkway, lounge area, guest room corridor. For the same material to hold up on both full-height arches and 3-meter-high corridor walls, it relies on uniform texture density + matte surface; if replaced with any material whose texture varies abruptly in depth, this project will look cheap.

The travertine series offers light beige, off-white, light sand and other colors, with the rest customizable; the visual tone of this case is based on light beige line texture as the base tone.

2.2 Material performance parameters

Project Parameter description
Composition of materialsComposite of natural mineral raw materials and polymer flexible substrate, an inorganic eco-material
Fabric processA stone-imitation decorative surface formed by pressing or printing according to the surface texture of the color
Environmental performanceNo added formaldehyde, no asbestos, meeting conventional environmental requirements for home and commercial decoration
Combustion performanceFlame retardant;The specific grade shall be subject to the valid test report of the selected model.
Waterproof and moisture-proofThe material does not absorb water, and after construction the wall is less prone to dampness and mold
UV resistance and weather resistanceHas UV resistance, high and low temperature resistance and weathering resistance, and can be used for exterior facades.
Anti-crackingFlexible base material can absorb the micro deformation of the base, and the surface is not easy to appear fine cracks
Can be bentThe panel has a certain flexibility and can be bent into an arc within a certain radius;The specific radius shall be subject to the model and substrate conditions.
Bonding methodFull-bed adhesion is recommended for installation; weather-resistant adhesive is required outdoors
Stain resistance and cleaningThe surface is dense and not prone to retaining dirt; for daily cleaning, wipe with water or a neutral cleaner.
Implementation standardsJG/T 540-2017 'Building Flexible Stone-faced Decorative Material'

Specifications and packaging parameters

Specifications (mm) Thickness (mm) Approx. weight per panel (kg) Wooden crate packaging (pieces/crate) Area per box (㎡)
1220×29302.5–3.51770Approx. 250.2

The specifications, weights and packaging in the table are reference values; actual values are subject to order confirmation; custom large panels, small panels and special-shaped sizes are supported.

3. Configuration plan

3.1 Allocate materials by spatial function

Space / Location Suggested materials Specifications Key focus
Lobby main wall / welcome backdropFlexible Stone(large panel format)1220×2930mmOverall feel, seam alignment
Cylindrical column / curved column claddingFlexible stone (curved wrapping)Same as aboveBending radius, seam positions
Elevator lobby / corridorFlexible StoneSame as aboveScrub resistance, corner finishing
Wall base 0–300mmSame as above, or add edge trimSame as aboveLuggage carts and cleaning equipment collisions

3.2 Quantity and project schedule estimate

Dosage formula (★engineering experience basis):

Material preparation area = measured net wall area × (1 + loss rate). Loss rate: regular walls 5%–8%; spaces with many corners/openings 10%–15%. Number of wooden crates = material preparation area ÷ 250.2㎡ (rounded up)
Item Calculation Result
Wall area of this project—Approx. 560 ㎡
Wastage rate★Value by spatial complexity10%
Material preparation area560 × 1.10Approx. 616 ㎡
Number of wooden crates616 ÷ 250.2 → Round up3 boxes

Construction period estimate (◆ estimate):

Stage Schedule
Substrate treatment (knock out hollow areas + leveling + drying)Substrate treatment usually accounts for about 1/3 of the total construction period
Layout setting-out★The denser the holes, the greater the layout workload
Adhesive mounting on wall★2 people can complete 60-100㎡ per day in a group; 560㎡ ÷ 80㎡/day ≈ 7 days
Finishing · Cleaning · Acceptance★Project experience
Total (budget estimate)Approx. 13 days(range 10–16 days)

Diameter specification: The table above is an estimate calculated by order of magnitude,Excludes time occupied by material transport and coordination with the client: ; the actual schedule is subject to the construction schedule confirmed after on-site survey.

A practical reminder: Flexible stone is made from natural mineral raw materials,Slight color tone differences may exist between different batches, this is a characteristic of the material itself. For large-area projects, it is recommendedStock the full quantity at one time and mix the layout: ; always use the same batch for the same wall in the same space.

3.3 Material Configuration

Stage Materials Function Basis
BondingSpecial adhesive,Full adhesion methodEnsure the finish and substrate are fully bondedProduct technical requirements; weather-resistant adhesive for outdoor use
SubstrateLeveling materials (selected according to substrate condition)Provide a flat, dry substrate free of hollowingSubstrate flatness directly affects appearance
Close upEdge trim / metal trimTreat internal and external corners, door frames, and wall base closures★Engineering Experience Practices
CuttingUtility knife / special cutting toolOn-site cutting according to the layout drawingOn-site secondary cutting is standard practice

IV. Construction process and acceptance control points

Flexible stone belongs toRelatively relaxed requirements for construction conditionsa type of material: no keel or complex substrate is required,Once leveling is complete, it can go on the wall—dry adhesion or wet fixing both work. But this does not mean that the process can be skipped.

Step 1 · Base treatment

Adhesive substrates includeCement mortar walls, concrete walls, gypsum board walls, lightweight partition walls, insulated wall surfacesRequirements:dry, free of floating dust, no hollowing: ; if flatness is insufficient, level first; if moisture content is too high, seal the base first.

★Engineering Experience: The most common problems in existing-building renovation projects are hollowing of the old putty layer, local dampness, and non-straight internal and external corners.Hollowing must be removed; otherwise the finish will fall off along with it.

Step 2 · Measurement and layout

It is advisable to put the layout drawing on paper before starting workMark door and window openings, switches and sockets, and internal and external corner positions, and calculate the space occupied by trim strips in advance.Joint lines on different walls within the same space should be aligned as much as possible, the overall visual impression differs greatly.

Step 3 · Cutting

Cut according to the layout drawing; secondary cutting on site is a conventional practice. Flexible stone panels are thin and flexible, making cutting less difficult than ceramic tile or stone, butAvoid repeatedly bending the same area.

Step 4 · Adhesive application and wall installation (full adhesion method)

RecommendedFull adhesion method: Adhesive should be selected according to the product instructions,Full coatingRather than spot application; after installation on the wall, press firmly and release air to ensure there is no cavity between the finish and the substrate.

Regarding curved arcs: Flexible stone can bend within a certain radius,The specific radius shall be subject to the model and substrate conditions.: ; large-radius curves require a mock-up for confirmation first.

Step 5 · Joints and edge finishing

  • Tight-joint: The seam lines are the finest, suitable for regular walls;
  • Leave a joint + edge trim: High fault tolerance, suitable for spaces with many corners and cutouts;
  • Metal trim: Used for closing edges and emphasizing lines.

Step 6 · Cleaning and self-inspection

Check each wall: hollowing, color difference, straightness of joint lines, squareness of openings, and finishing in place.

Step 7 · Delivery acceptance

Control points Standard value or practice Basis
Substrate dryness / hollowingdry, free of floating dust, no hollowing; if not compliant, repair first★Engineering Experience Practices
Substrate flatnessLeveling in place, repair deficiencies first★Engineering Experience Practices
Bonding methodFull bonding method, adhesive selected according to product instructionsProduct technical requirements
Material execution standardJG/T 540-2017 'Building Flexible Stone-faced Decorative Material'Product execution standard
Internal and external corners and closuresEdge trim / metal trim closure, trim straight and true★Engineering Experience Practices
Cutouts and panelsThe cutout position is coaxial with the panel, and the edges are not chipped★Engineering Experience Practices
Color difference controlUse the same batch of material for the same wall surface in the same space★Engineering Experience Practices
Joint straightnessAlign joint lines within the same space, with no obvious misalignment visually★Engineering Experience Practices
Environmental protection indicatorsNo added formaldehyde, no asbestosProduct information (subject to the test report for the model)

V. Image display and application description

Total application photos of this project 10 pieces; all photographed on site at the project, covering elevator hall, wall texture close-up, lounge area, curved corridor, arched corridor, column cladding, curved wall detail, lobby lounge area, guest room corridor, elevator hall passage and other areas.

Close-up of a hand touching a sample, horizontal texture and pores on a light beige finish
Figure 1 · Close-up of hand-touched sample, horizontal grain and pores on light beige finish
Elevator lobby, light beige horizontal-grain wall and dark door leaves
Figure 2 · Elevator hall, light beige horizontal-textured wall and dark door leaves
Rest corner, light-colored horizontal-textured wall and blue armchair
Fig. 3 · Lounge corner, light-colored horizontal-texture wall and blue armchair
Curved corridor, light-colored horizontal-grain wall with continuous contour lighting
Figure 4 · Curved corridor, light-colored horizontal-grain wall and continuous contour lighting
Arched elevator lobby, light-colored finished door opening with elevator doors on both sides
Figure 5 · Arched elevator lobby, light-colored finished door openings and elevator doors on both sides
Close-up of a cylinder, light beige horizontal texture finish with dark floor
Figure 6 · Close-up of the cylindrical column, light beige horizontal-texture cladding and dark floor
Wall close-up, light-colored horizontal texture with gold curved decoration
Figure 7 · Wall close-up, light-colored horizontal texture and gold curved decoration
Lobby lounge area, light-colored columns, textured wall and seating
Figure 8 · Lobby lounge area, light-colored cylindrical columns, textured wall and seating
Guest room corridor, light-colored horizontal-grain wall and continuous door leaves
Figure 9 · Guest room corridor, light-colored horizontal-grain wall and continuous doors
Corridor corner: light-colored wall, arched doorway and plants
Figure 10 · Corridor corner, light-colored wall, arched doorway and plants

VI. Communication and confirmation process

For the wall engineering of a hotel lobby project, communication mainly revolves around three things:Whether the material selection matches the spatial character, how the openings and layout are determined, and whether the substrate conditions are met. The following are the key points of the communication process.

Owner: Ours is a hotel lobby, and we want the wall to have the texture a hotel lobby should have. What do you suggest?

IGOODS: It is advisable to clarify three things first: gloss level (matte rather than high-gloss), texture intensity (subtle textures are more enduring), and whether curved shapes are needed. For materials such as linear travertine in the travertine series, the performance of the light beige linear texture is relatively stable and can be adapted.

Owner: How should cutouts and panel joints be handled?

IGOODS: This must be atLayout stageSolve it. We will first map the positions of door and window openings, switches and sockets, and internal and external corners onto the layout drawing, then determine the seam line direction. Deciding on site will force the seam lines to be disrupted by openings, which is the most common appearance problem.

Owner: What should be noted about the base layer?

IGOODS: the base layer mustdry, free of floating dust, no hollowingHollowing must first be removed and re-leveled—the finish is applied on top, and if the substrate is hollow, the finish will fall off with it; walls with excessively high moisture content must be primed and sealed first.

Owner: Will it be easy to clean later?

IGOODS: The surface is dense; for daily cleaning, just wipe with water or a neutral cleaner. Note: do not use strong solvents, and no sanding is needed.

Owner: To what extent is it dirt-resistant and scratch-resistant?

IGOODS: The specific wear resistance and stain resistance indicators shall be subject to the valid test report of the selected model. The material itself is zero formaldehyde, asbestos-free and flame retardant; these can be verified in the product documentation.

What was confirmed in this communication?

  • Selection criteria: Determine the direction of matte, textured, bendable materials rather than high-gloss surface materials;
  • Layout prerequisites: Doors and windows, openings, and internal and external corners must be positioned during the layout stage, not decided on site at the last minute;
  • Substrate prerequisites: Hollowing must be removed and leveling redone, and wall installation is allowed only after moisture content meets the standard;
  • Batch control: Use the same batch of material for the same wall surface in the same space to avoid color differences;
  • Acceptance Basis: Performance indicators are subject to the valid test report for the selected model; no verbal commitments are made.

Record notes: This section is a summary of key points from the communication process, used to explain how the plan was finalized. The text contains no performance commitments or price commitments;The avatar and nickname are illustrative graphics and do not represent the customer's actual image.

Seven, usage effects and daily maintenance

7.1 What is the perception of space?

The first change after Line Texture Travertine is installed on the wall is the walkway "got longer". The fine, dense horizontal layering forms continuous guiding lines in perspective, and guests walking in the corridor will naturally move forward along the direction of the texture—this is something hard ceramic tiles cannot achieve; the seam lines of tiles are vertically divided, and the farther you walk, the more it looks like it has been cut into segments.

The second change is in the arched corridor: at the junctions of the inclined surface, curved surface and door frame of the continuous arches, after covering the entire piece with the same material, the outline of the arch becomes a continuous curve, rather than a patchwork of several pieces of material.

7.2 Daily maintenance

Scenario Treatment method
Daily floating dustdry cloth or feather duster
Water stains / beverage stainsWipe with clean water or neutral detergent
Oily stainsNeutral cleaner,Avoid strong solvents
Minor scratchesJudged by texture type; textured surfaces themselves are relatively tolerant of minor marks
Prohibited practicesStrong acid and strong alkali solvents, steel wool, grinding machines

Maintenance-related characteristics of the material itself (from product documentation):

  • Waterproof and moisture-proof: The material does not absorb water, so walls are less prone to dampness and mold after construction;
  • Mildew resistance: Suitable for humid environments and underground spaces; routine maintenance is mainly wiping;
  • Anti-crackingThe flexible substrate can absorb minor substrate deformation, making the finish less prone to fine cracks;
  • Stain resistance and cleaning: The surface is dense and not prone to staining; daily wiping with water or neutral cleaner is sufficient.

7.3 On-site Recheck After Delivery

Review items Inspection content Basis for determination
Joints and closuresWhether joint lines are straight, whether lines are aligned, whether corners are properly executedno obvious misalignment by visual inspection
Cutouts and panelsWhether the switch and socket are coaxial with the cutout and whether the edges are chippedPanel coverage with no exposed edges
Whole wallWhether there is hollowing or obvious color differenceHollowing rate 0; no visible color difference on the same wall

Diameter specification: The above are the conventional characteristics of the material itself and the review method.For engineering indicators in specific projects (wear cycles, stain resistance grade, etc.), please refer to the valid test report of the selected model and project technical confirmation.

7.4 Cost Reference

Flexible stone'sPrice range is 25–300 yuan/㎡, the span is relatively large, depending on specifications, thickness, texture process, order quantity, and delivery time.

Cost rough estimate for this project (◆ rough estimate): Apply at 25–300 yuan/㎡ to the budget estimate area:

Item Calculation Result
Lower limit of material amount560 × 25Approx. RMB 14,000
Upper limit of material amount560 × 300Approx. RMB 170,000

Why is the range so wide: 25–300 CNY/㎡ covers the full range from economy texture to custom large slabs, the actual unit price depends on specifications, thickness, texture technology, order quantity and delivery time.The actual transaction amount of this project is subject to the contractnot disclosed on this page.

VIII. Common questions (FAQ)

Will large-format panels on walkway walls feel oppressive?

On the contrary. The clear width of the corridor is limited, fewer vertical seams means more transparency. Small-sized tiles form dense vertical line divisions in a 1.5-meter-wide corridor, visually dividing the space into segments; large-format tiles reduce the number of vertical joints, and with the horizontal stratification of textured holes, the depth is actually elongated.

How should the junction between the door casing and wall be handled?

This is where corridor terminations are most concentrated. The method is first place the positions of door frames, fire hydrants and inspection openings onto the layout drawing, then determine the seam line direction so that the seam lines avoid these points. Deciding on site at the last minute will make the sealing of a row of doors form an obvious jagged line—with nine doors in a row, a single deviation of 2mm will be noticed.

Line Texture Travertine and Printed travertine What is the difference?

Printed travertine retains the pores and irregular layering of travertine, with a stronger texture and a closer resemblance to natural travertine; the layering of linear travertine is processed into more regular parallel lines, looks cleaner from a distance, with stronger perspective guidance, suitable for spaces such as corridors and galleries that need depth.

Will paintings and decorative strips on the wall disrupt the continuity of the texture?

No, but the location must be reserved during the layout stage. The pre-buried points for hanging paintings, decorative strips, and wall lamps should be marked on the layout drawing first, and the seam lines should avoid these points, otherwise the decorative parts will press on the seam lines when installed, looking awkward.

IX. Project File and Contact Information

Project file Content
Project typeHotel lobby
Materials usedLine Texture Travertine (Travertine Series)
Material specifications1220×2930mm | thickness 2.5–3.5mm | single piece about 17kg
Packaging70 Sheets/Case | Approximately 250.2㎡/Case
Construction processFull bonding method, direct wall installation after leveling, no keel required
Implementation standardsJG/T 540-2017 'Building Flexible Stone-faced Decorative Material'
Project locationEmeishan City, Sichuan Province
Wall areaApprox. 560 ㎡ (◆ budget estimate)
Actual photo record10 pieces

Chengdu Igoods Technology Co., Ltd. (IGOODS) Flexible Stone · PU stone skinwall panel · wood paneling wall · WPC grid panel · Same color wall cabinet door

  • Phone / WeChat / WhatsApp: 19136341389
  • Email: 19136341389@163.com
  • Address: Room 9001, 9th Floor, Building A, No. 166 Laifeng 5th Road (Laifeng Digital Innovation Center), Wuhou District, Chengdu, Sichuan Province, China
  • Services: Free sample delivery · Selection advice · Project quotation · Installation guidance · After-sales response

Content and scope statement: This page records the wall material selection and construction process for this hotel lobby. The material specifications, performance parameters and applicable standards in the text all come from IGOODS product materials and can be verified independently; values marked "★ Engineering Experience" are common industry practices and empirical ranges and are not cited as national standard data; those marked "◆EstimateThe area, schedule, and cost are estimated values calculated according to common industry magnitudes, used to judge the order of magnitude, not measured bills; actual values are subject to project confirmation. The cost section is only used to explain the pricing logic and does not represent an actual bill. The full text contains no performance promises, price promises, or brand rankings. Images are used to display materials and spatial applications; communication materials must be verified against original records and are not to be used as customer acceptance or measured proof.

Find the appropriate wall expression for your project.

Provide the type of space, wall area, and design intention. Communicate about materials, samples, and quotations.

Consulting project material selection ↗
Contact phone number Product Catalog Free Sample
WeChat ID copied