Corporate reception and office space 520㎡ woven hemp flexible stone (vintage bronze) wall construction case

The corporate reception and office space project is located in Langzhong City, Sichuan Province. The main wall material is woven hemp flexible stone (vintage bronze), used for the reception feature wall, corridor facades, and meeting area column cladding. The construction area is approximately 520 ㎡ (including public areas), completed by 3 workers in 11 working days.

Published time:

Introduction

The corporate reception and office space project is located in Langzhong City, Sichuan Province, and the main wall material selected is Linen weave flexible stone Flexible Stone (retro bronze), used for the reception backdrop wall, corridor facade and conference area column cladding, with a construction area of about 520 ㎡ (including public areas), completed by 3 people in 11 working days. This article explains the material selection basis, quantity and schedule estimates, construction control points, application images and common questions all at once.

  • Project: Corporate reception and office space · reception background wall, corridor elevations and meeting area column cladding
  • Location: Langzhong City, Sichuan Province
  • Main material: Hemp weave soft stone flexible stone (vintage bronze)
  • Construction area: approx. 520 ㎡
  • Schedule: 11 working days / 3 people
  • Implementation standards: JG/T 540-2017

Project file

Project Content
Project nameOffice space wall material—printed soft stone (vintage bronze) real project case (Langzhong)
Space typeMaterial actual shooting
Business typeCorporate reception and office space
CityLangzhong City, Sichuan Province
ScaleReception desk + corridor + meeting area
Construction locationFront desk backdrop wall, corridor elevation, and meeting area column cladding
Main material.Linen weave flexible stone (vintage bronze)
Construction areaApprox. 520 ㎡ (including public areas)
Construction period11 working days
Number of construction workers3 people
Implementation standardsJG/T 540-2017"Flexible Stone-like Facing Materials for Buildings"

1. Customer industry usage scenario: the real wall requirements of corporate reception and office spaces

  1. The front desk space should be "textured but not ostentatious" The corporate reception is the first stop where visitors linger, so the wall must support the corporate image without overpowering the reception staff and negotiation area. Low-saturation, matte materials are usually more suitable than high-contrast materials.
  2. The same color code must adapt to both cool and warm light Office spaces often mix 4000K cool light with 3000K warm light. The degree to which a color number shifts under the two types of light determines the stability of the wall—if it shifts too far, different areas on the same floor will look like two different materials.
  3. Finishing of door frames in corridors and elevator lobbies Corridors in office spaces have dense doors, elevator door surrounds, and fire equipment cabinets. Every opening is a closure point; when closure pieces match the main material in color, the elevation looks clean.
  4. Junction of glass partition Glass partitions are commonly used in the reception desk and meeting areas. Cut edges of panels need to be covered with trim, and a sealant gap should be left between the panel and the glass to avoid direct hard contact between two hard materials.
  5. Seam position for column wrapping The structural column in the front desk area is usually located in the middle of the circulation path and is visible from all four sides. The seams must be arranged at the side and rear so that no joints are visible from the front, and only then does the column surface look like a single solid piece.
  6. Maintenance costs should be low Cleaning frequency in corporate spaces is lower than in food and beverage venues, so materials that easily retain marks will look dirty over time. Materials with a dense surface that can be wiped with a neutral cleaner are more suitable.

II. Material comparison: why choose "hemp-woven soft stone flexible stone"

When comparing wall materials side by side, what really determines the selection is often not "which one looks better," but rather whether the base layer can bear the load, whether the schedule can be compressed, and whether the shape can be achieved.

Comparison item Linen weave flexible stone Tile / Slab. Natural stone. Traditional wood veneer
Weight per square meterApprox. 5.0–5.6 kg/㎡Noticeably heavier, substrate reinforcement requiredHeaviest; mostly requires dry hangingIncludes thicker base coat
thickness3.5–5.5 mm6–12 mm15–30 mmIncludes base coat 15 mm or more
Curved surface and columnCan be curved within a certain radius, covering the entire surfaceSmall pieces must be cut and pieced together, with dense jointsRequires waterjet processing; cost and lead time increaseRequires steam heat bending or slitting
Construction methodNo skeleton required, full adhesion after leveling the baseSpecial adhesive, high requirements for joint-gap processMostly dry-hung, requires embedded partsRequires furring strips or a backing board
Moisture-proof and mold-proofDoes not absorb water, does not swellIt does not absorb water itself, but dirt easily collects in the seamsSome stone absorbs waterProne to swelling and mold when damp
ScheduleShort, no wet work or paintingMediumLengthLength
Points to noteNot recommended for ground installationNot good at curved surfacesNot good at special shapesNot good at wet areas

Description: The values in the table above are common ranges for various materials, used to illustrate applicable boundaries and not constituting a ranking of any material. For this project, woven hemp soft stone flexible stone was ultimately selected because the vintage bronze soft stone leans gray under cool light and copper under warm light, offering two looks in one color.

2.0 Why choose Linen weave flexible stone

The owner wanted a material that "doesn't look like stone or wood, has a metallic feel but isn't glossy." The base material of Vintage Bronze woven flexible stone is a woven texture with a matte surface—grayish under cool light and coppery under warm light, so one color code covers two lighting environments; the woven texture has a handmade feel up close and reads as a soft, uniform base color from a distance, exactly fitting a reception area where you "want texture but don't want it to steal the show."

2.1 Three questions for selection

Condense the selection into three questions, and the direction can basically be set:

  1. Is the wall curved or column-shaped? Yes → prioritize flexible materials that can bend; No → then compare weight and construction period.
  2. Can the substrate bear the weight of the stone? Cannot (lightweight partition walls, old walls, insulated walls) → prioritize flexible materials; can → natural stone is also an option.
  3. What kind of atmosphere does the space want? Columns are covered in one piece, with seams kept away from the main viewing direction.

The answers to the three questions for this project: the vintage bronze soft stone appears grayish under cool light and coppery under warm light, giving one color two impressions; the woven texture has a handmade feel up close and reads as a soft overall base color from a distance; and the column is fully wrapped in one piece, with seams on the column surface kept away from the main viewing direction. Therefore, woven-texture soft stone flexible stone was selected.

3. Configuration plan

3.1 Material specifications and packaging

Specifications (mm) Thickness (mm) Approx. weight per panel (kg) Wooden crate packaging (pieces/crate) Area of wooden crate after packaging (㎡) Weight after packaging approx. (kg)
600×12003.5–5.54220158.4920
1200×30003.5–5.520602161355

Optional colors: New South Red, Old South Red, Beige (other colors can be customized).

Texture and light perception notes: The woven texture of hemp weave soft stone has an obvious handmade feel up close, while from a distance it reads as a whole soft base color.

3.2 Allocation by space

Different parts of the same project do not have the same requirements for materials. The table below breaks down the actual space of a corporate reception and office space and explains why each part is specified this way.

Space / Location Area share ★ Material usage Why set it this way?
Main viewing surface (the first wall directly facing you when entering)20% or soFull-piece laying, seams kept away from the centerWhere the line of sight rests longest, the overall appearance is most complete
Side walls and passagewaysabout 35%Conventional installation, with joints aligned continuouslyLarge area, with the focus on smooth, continuous seams
Curved wall / partitionabout 15%Full-piece curved wrappingPiecing curved surfaces into small pieces creates dense diagonal seams
Column wrappingabout 8%%Full-piece wrapping on the column surface, with seams kept at the sides and rearThe key is that no seams are visible from the front
Door openings and window casingsabout 10%Use matching termination pieces; do not butt-join on siteCut edges easily expose the panel backing
Form and local areasAbout 12%%Custom-shaped panels according to drawingsOn-site cutting precision for irregular pieces is insufficient

★Description: The proportions in the table above are common distributions for similar restaurant/hotel spaces and are used to estimate material quantities for each part; actual quantities are subject to on-site measurement and layout drawings.

3.3 Estimation of Quantity and Construction Schedule

The calculation process is given below so it can be reviewed according to your own project's basis.

Project Calculation formula Result
Net installation areaOn-site measurement (including public areas)Approx. 520 ㎡
Material preparation area520 × (1 + 12% loss)Approx. 582 ㎡
Number of wooden crates582 ÷ 158.4 square meters per box, round upApprox. 4 boxes
Substrate treatmentLeveling, repair, primer2–3 working days
Layout setting-outSnap lines, align seams, set the starting point1-2 working days
Adhesive mounting3 people per group, average 60-100㎡ per day ★Approx. 7 business days
Finishing and acceptanceEdge trim, cleaning, acceptance1-2 working days
TotalConfigure for 3 people11 working days

3.4 Material List

Auxiliary materials Purpose Description
Special adhesiveMain material for full-surface bonding methodSelect according to product instructions; use weather-resistant type for outdoor or damp areas
Interface agentSubstrate sealingSelect according to substrate material
Edge trim / internal and external corner piecesCorners and closuresSame color family as the main material; prioritize matching accessories rather than on-site cutting
Joint filler materialJoint sealingClose to the main material color number to avoid overly prominent joint lines
DetergentCompletion cleaningNeutral cleaner; strong acids and alkalis prohibited

IV. Construction process and acceptance control points: on-site practice for "hemp-woven soft stone flexible stone"

4.1 Seven steps

  1. Substrate inspection: Moisture content, flatness, and strength must all pass. Flatness is checked with a 2 m straightedge; sanding and loose layers must be removed down to a solid substrate, and hollow areas must be knocked out and redone.
  2. Substrate treatment: Walls with high moisture content require a sealing primer first; different interface agents are selected for different substrates.
  3. Layout setting-out: Put the layout plan on paper before starting work; mark door and window openings, switches, sockets, and internal/external corner positions; align seam lines across different walls in the same space where possible.
  4. Cutting processing: Cut to layout dimensions; cover cut edges with trim or pressure strips; determine opening positions at the layout stage.
  5. Full bonding installation: The full-surface bonding method is recommended, starting from the main viewing face and progressing to both sides and upward; apply along the arc direction at curved areas.
  6. Finishing treatment: Internal and external corners use matching trim pieces; junctions with door frames, ceilings, and floors are executed according to the node drawings.
  7. Cleaning acceptance: Use a neutral cleaner to remove residual adhesive and fingerprints, and check item by item according to the acceptance checklist.

4.2 Acceptance Control Sheet

Inspection items Control points Criterion
Substrate flatness2 m straightedge inspectionGap not exceeding 3mm ★
Substrate moisture contentSeal damp areas firstNo obvious moisture marks, no water seepage
Joint line alignmentAlign joint lines within the same spaceSmooth and free of steps by visual inspection
Curved-surface installationDirection along the arcNo obvious sharp folds, no edge lifting
External corner closureUse matching termination piecesNo exposed board bottom, consistent color
HollowingSpot-check by tapping each pieceHollowing rate not exceeding 5% ★
Surface cleaningNeutral cleanerNo residual glue, no scratches

The specific allowable deviation values shall be subject to the standards and contract terms of the project location; the table above shows the common industry practice ranges.

4.3 Special methods for arc and column

Curved walls, columns and irregular corners are where flexible materials differ most directly from traditional finishes. There are several points that must be confirmed in advance for the installation method:

Location The method. Items to confirm in advance
Large-radius curved wall (R ≥ 2m)Full-piece curved application, seam following the curve directionArc radius, panel thickness, ambient temperature
Small-radius curved wall (R < 2m)Test the bend first; when there is obvious springback, switch to narrow-strip splicingMust first test bending with a physical mock-up
Cylindrical column claddingFull-piece wrapping, seam left at the side rearColumn diameter and whether there are embedded parts on the column surface
Arches and door openingsContinuous curve, use matching termination piecesDoor opening squareness
Internal and external cornersUse matching termination pieces; do not butt-join on siteWhether the color of finishing pieces is consistent with the main material

4.4 Common problems and avoidance

Phenomenon Reason Workaround
Joint misalignmentUneven substrate, cumulative error block by blockFirst snap lines to control continuous joints, and start installation from the main sightline
Curved-surface edge liftingRadius smaller than the material's usable rangeTest bending before installation to confirm; change to narrower strips if necessary
External corner showing through to the substrateOn-site cutting and butt-joiningUse matching inner and outer corner pieces
The light strip reveals the jointsJoint conflicts with the position of the light stripDetermine the joints together with the light strips during the layout stage
Color difference concentrationMixing different batchesOrder enough at once for the same batch, and mix materials before installation
HollowingBase-layer sanding and insufficient adhesive dosageSubstrate treatment in place, full-adhesion installation

4.5 Construction tools and personnel allocation

Project Configuration Description
Measuring tools2 m straightedge, level, tape measure, chalk lineBase-layer acceptance and chalk-line layout
Cutting toolsUtility knife / board cutting knife, straight rulerOn-site cutting according to layout dimensions
Mixing toolsElectric mixerMix the adhesive according to the specified ratio
Adhesive application toolsNotched trowelFull-surface bonding method: control consistent adhesive layer thickness
Compaction toolPressure roller / rubber malletRemove air bubbles and ensure full adhesion
Cleaning toolsSoft cloth, neutral cleanerCompletion cleaning
StaffingAdhesive mounting, 2–4 people per team ★This project is staffed with 3 people
Daily production capacity per group60–100 square meters per group ★Related to substrate conditions and modeling complexity

★Description: Staffing and daily capacity are common industry ranges, used to estimate the construction period; actual efficiency is affected by substrate conditions, shape complexity, floor height and on-site access conditions.

V. Image display and application description

5.1 Indoor Side Desk

Indoor side counter, bronze mottled-texture backdrop wall with hanging picture
Figure 1 · Interior side counter, bronze mottled-texture feature wall and framed artwork

5.2 Resting Area

Rest area, bronze-textured feature wall with sofa and coffee table
Figure 2 · Rest area, bronze-textured background wall with sofa and coffee table

5.3 Side View of Rest Area

Rest area side view, bronze-textured wall with green seats
Fig. 3 · Lounge side view, bronze-texture wall and green seating

5.4 Visitor Corner

Reception corner, bronze-textured background wall and side liquor shelving
Figure 4 · Reception corner, bronze-texture background wall and side beverage shelving

5.5 Conference area

Meeting area, bronze-textured background wall, wooden table and leather chairs
Figure 5 · Meeting area, bronze-textured background wall, wooden table and leather chairs

5.6 Display side stand

Display side counter, bronze textured background wall with hanging picture and vase
Figure 6 · Display side table, bronze-texture background wall with framed picture and vase

VI. Communication and confirmation process

The following are several questions confirmed by both parties during material selection and construction, organized in the order of the conversation.

  • Design party: Want a material that doesn't look much like stone or wood, with a slight metallic feel but not glossy.
  • Our side: You can look at the Vintage Bronze pattern; the substrate is hemp-woven soft stone with a matte woven surface—grayish under cool light and coppery under warm light.
  • Owner: Will it be too distinctive, with low client acceptance?
  • Our side: It is recommended to request samples first and view them under the actual lighting. This color family is actually fairly stable in office spaces because its saturation is low.
  • Construction party: There are columns to wrap—can columns be covered with a single piece?
  • Our side: Yes. Arrange the column seams at the rear side so the front view is a complete piece.

Scope statement: The above is a written summary of the communication content, used to explain the decision-making process; it does not represent a commitment to results, and the contract terms and on-site conditions shall prevail.

Seven, usage effects and daily maintenance

7.1 Perception and light environment

The woven texture of linen weave flexible stone has an obvious handmade feel up close and reads as a whole soft base color from afar. The same wall looks different under different color temperatures: warmer under warm light and more neutral under cool light, which is also why it is recommended to first send physical samples for comparison under actual lighting.

7.2 Daily maintenance

Project The method. Note
Daily cleaningWipe with clean water or neutral detergentDo not use strong acids or strong alkalis
Oil stain treatmentNeutral cleaner + soft clothDo not use steel wool
Localized damageIndividual panels can be replacedReplaceable conditions were retained during layout
Damp areasMaintain ventilationDoes not absorb water, does not swell
Outdoor areasRegular washingExecute according to the design scope

7.3 Post-delivery Recheck Sheet

Review items Suggested timing Points of concern
Joints and closures7 days after handoverWhether there is lifting or cracking
Hollowing30 days after handoverSampling and tapping inspection
Color consistency30 days after handoverComparison across different walls and different floors
Cleaning statusDailyWhether there are stubborn stains

7.4 Intersection with Adjacent Materials

Wall materials rarely exist alone; there will always be neighbors such as ceilings, floors, wood veneer, metal parts and glass. How well the junctions are handled directly determines whether the elevation looks "clean" or "fragmented."

Adjacent materials Transition method Note
Ceiling / suspended ceilingPress the edge with a top trim strip, or leave a 3–5 mm revealJoint width must be consistent over the full length
Floor / skirtingSkirting line presses the lower edge of the panelDo not let the bottom edge sit directly on the floor, to avoid dragging wear
Wood finishTransition within the same color family, with the joint left at an internal cornerPlacing the two materials on the same wall requires comparing color differences first
Metal edge trim stripMetal strips press the seam, with the direction parallel to the grain directionColors are mainly matte dark tones to avoid stealing the show
Glass partitionUse a pressure strip for finishing, leaving a caulking gap between the glass and the panelCut edges of the panel need to be covered with trim
Door and window casingsUse matching termination pieces; do not butt-join on siteDoor opening squareness directly affects the finishing result

7.5 Cost Estimation

The cost of a wall consists of three parts: main material + auxiliary materials + labor. The budget estimate basis is as follows (◆budget estimate, not an actual measured bill):

Composition Scope Influencing factors
Main material.Preparation area approx. 582 ㎡ ÷ 158.4 ㎡ per boxColor, thickness, specifications, batch
Auxiliary materialsAdhesive + primer + trim pieces + groutSubstrate conditions, termination complexity
ManualMounting area × labor cost per unit areaForm complexity, floor height, proportion of special shapes

◆Estimate: Specific unit prices vary with pattern, thickness, order quantity, and construction conditions; a wide range is normal. This article does not provide a single quotation to avoid misleading; for project pricing, please provide the area, pattern, and delivery location.

VIII. Common questions (FAQ)

Below are the questions most frequently asked about material selection and construction in this project.

Is linen weave flexible stone suitable for a space like material close-up photography?

Suitable. The woven texture of the linen-woven flexible stone has an obvious handmade feel up close and reads as a whole soft base color from a distance. This project uses it for the front desk backdrop wall, corridor facade and meeting area wrapped columns. The vintage bronze flexible stone leans gray under cool light and bronze under warm light, one color with two impressions.

Can curved walls and column cladding be done in one continuous piece?

Yes. The material has a certain flexibility and can be bent within a certain radius, so columns, curved walls and irregular corners can achieve full-panel wrapping with continuous seams. The specific usable radius depends on the selected model, thickness and substrate conditions; it is recommended to first test-bend a physical sample at the corresponding curvature to confirm.

How long does the schedule generally take?

This project is approximately 520 ㎡, staffed with 3 people, and completed in 11 working days (including substrate preparation and finishing). The installation itself accounts for about 7 working days, with the remainder for substrate work, layout marking, and acceptance inspection. The main variable in the schedule is substrate condition—substrate rework will directly eat into the time saved on installation.

Can it be used in damp areas?

Yes. The material itself does not absorb water, and after construction the wall surface is not prone to dampness or mildew, so it can be used in humid environments and underground spaces. For wet areas such as bathrooms, it is recommended to confirm the specific scope in conjunction with the wet/dry zoning plan.

What about fire performance?

The material has flame-retardant properties; the specific combustion performance ratingshall be in accordance with the valid inspection report of the selected model. If the project has specific requirements for fire rating, please specify before placing an order.

How much difference in texture is there compared to natural stone?

Differences are visible up close: natural stone has naturally occurring random variation, while the texture of Linen Weave Soft Stone flexible stone is formed by embossing or printing, giving greater consistency within the same product. From a distance the overall look is similar. When placing natural stone and flexible materials on adjacent walls in the same space, it is advisable to make a small sample comparison first.

Can old walls be renovated by direct pasting?

If the original wall surface is firm and has no hollowing, it is possible; old tile surfaces can also be covered directly. But before construction, each surface must be checked for hollowing, and hollowed areas must be knocked out and redone—this step cannot be skipped.

Does the material have test reports? What standard does it follow?

Execution JG/T 540-2017 'Building Flexible Stone-faced Decorative Material' (issued by the Ministry of Housing and Urban-Rural Development). Environmental protection and combustion performance test reports for the corresponding models can be provided with the goods.

How to confirm color and texture?

It is advisable to request physical samples and compare them under the project's actual lighting before deciding the color number. There are differences between screen display and actual materials; in particular, stone-texture materials look different at different angles and color temperatures.

Can a single damaged panel be replaced later?

Yes. During layout, the seam lines and termination positions have already been determined, and a single piece can be pried out from the termination for replacement. It is recommended to reserve 1–2 boxes of same-batch material as spares at delivery.

IX. Project File and Contact Information

Project Content
Project nameOffice space wall material—printed soft stone (vintage bronze) real project case (Langzhong)
LocationLangzhong City, Sichuan Province
Main material.Linen weave flexible stone (vintage bronze)
Material seriesCloth Texture and Weave Series
Construction areaApprox. 520 ㎡
Schedule11 working days
Related sectionsProject Cases · Material actual shooting
Implementation standardsJG/T 540-2017

Similar projects can be found at Project Cases View column; for material specifications and colors see Cloth Texture and Weave Series.


Legend and specification notes

  • ★Project experience = Industry common practice and experience range, not a reference for national standard data.
  • ◆Estimate = Estimated value calculated based on the scale,not an actual measured bill; actual conditions are subject to the contract agreement and site conditions.
  • Material parameters are taken from the corresponding product file; combustion performance, environmental grade, etc. are subject to the valid test report for the selected model.
  • Area, schedule, and quantity are estimates based on industry-scale figures; the calculation process is provided and can be reviewed against your own project's basis.

Find the appropriate wall expression for your project.

Provide the type of space, wall area, and design intention. Communicate about materials, samples, and quotations.

Consulting project material selection ↗
Contact phone number Product Catalog Free Sample
WeChat ID copied