Construction case of rough rammed earth (New South Red) wall surface in a 1050㎡ Chinese-style hot pot restaurant

The Chinese-style hot pot restaurant project is located in Banan District, Chongqing, and the main wall material selected is rough rammed earth flexible stone (New South Red), used for the hot pot restaurant's entrance hall, lobby main wall and corridor walls. The construction area is about 1050 ㎡, completed by 4 people in 19 working days.

Published time:

Introduction

The Chinese-style hot pot restaurant project is located in Banan District, Chongqing, and the main wall material selected is Coarse rammed earth Flexible Stone (New South Red), used for the entrance hall, main hall main wall, and corridor walls of a hot pot restaurant, with a construction area of about 1050 ㎡, completed by 4 people in 19 working days. This article explains the material selection basis, quantity and schedule estimation, construction control points, application photos, and common questions all at once.

  • Project: Chinese-style hot pot restaurant · hot pot restaurant entrance hall, main hall walls and passage walls
  • Location: Banan District, Chongqing
  • Main material: Coarse rammed earth flexible stone (New South Red)
  • Construction area: Approx. 1050 ㎡
  • Schedule: 19 working days / 4 people
  • Implementation standards: JG/T 540-2017

Project file

Project Content
Project nameHot pot restaurant wall material recommendation - New South Red Rammed earth board flexible stone application case (Chongqing Banan)
Space typeFood & Beverage Spaces
Business typeChinese-style hot pot restaurant
CityBanan District, Chongqing
ScaleMain hall, 30 tables + 8 booth groups
Construction locationWalls of the entrance hall, main hall and corridor in a hot pot restaurant
Main material.Coarse rammed earth flexible stone (Xinnanhong)
Construction areaApprox. 1050㎡
Construction period19 working days
Number of construction workers4 people
Implementation standardsJG/T 540-2017"Flexible Stone-like Facing Materials for Buildings"

1. Customer industry usage scenario: the real wall requirements of a Chinese-style hot pot restaurant

  1. Mainly for the evening market; the wall surface must hold up under warm light. The daily peak of a hot pot restaurant is after evening, and the lighting is mainly warm spotlights and light strips. The expressive power of the material comes from the height differences in the texture, and only under angled light does it show light-dark undulation; glossy materials under the same lighting will only become a patch of light spots.
  2. Long-term effect of boiling steam on wall surfaces. The steam output of hot pot is much higher than that of ordinary Chinese cuisine, and the walls are in a high-humidity environment for a long time. Non-water-absorbing material is the bottom line, otherwise repeated moisture exposure will accelerate the aging of the adhesive layer, and the first problem usually appears at the board edges.
  3. First-glance color weight of the entrance hall and main hall. If the red tone of a hot pot restaurant is spread over the entire wall, it can easily become cloying, so wood grilles, dark floors or plants are needed for balance. When choosing colors, the ceiling and floor must be considered together; do not fixate on only one wall.
  4. Surface density in cooking fume environments. Cooking fumes will adhere to all vertical surfaces. Materials with dense surfaces can be wiped clean with neutral cleaning agents; once oily dirt is absorbed into materials with high porosity, it is very difficult to remove completely.
  5. Scrub resistance of the condiment station and cashier counter. The self-service condiment station and cashier counter are places where customers repeatedly stop, and the wall surface is easily brushed by elbows and trays. When laying out, avoid the height band of frequent contact, or use cleanable edge trim pieces as transitions.
  6. Open right after renovation, with no off-gassing period. Dining projects generally open right after renovation, with no time window for ventilation to dissipate odors. The material is formed from natural mineral raw materials combined with a polymer flexible substrate, does not use wood substrates, has no added formaldehyde, and is asbestos-free—this is the basic threshold for dining spaces.

II. Material comparison: why choose "coarse rammed earth flexible stone"

When comparing wall materials side by side, what really determines the selection is often not "which one looks better," but rather whether the base layer can bear the load, whether the schedule can be compressed, and whether the shape can be achieved.

Comparison item Coarse rammed earth flexible stone Tile / Slab. Natural stone. Traditional wood veneer
Weight per square meterApprox. 4.0–4.4 kg/㎡Noticeably heavier, substrate reinforcement requiredHeaviest; mostly requires dry hangingIncludes thicker base coat
thickness2.5–3 mm6–12 mm15–30 mmIncludes base coat 15 mm or more
Curved surface and columnCan be curved within a certain radius, covering the entire surfaceSmall pieces must be cut and pieced together, with dense jointsRequires waterjet processing; cost and lead time increaseRequires steam heat bending or slitting
Construction methodNo skeleton required, full adhesion after leveling the baseSpecial adhesive, high requirements for joint-gap processMostly dry-hung, requires embedded partsRequires furring strips or a backing board
Moisture-proof and mold-proofDoes not absorb water, does not swellIt does not absorb water itself, but dirt easily collects in the seamsSome stone absorbs waterProne to swelling and mold when damp
ScheduleShort, no wet work or paintingMediumLengthLength
Points to noteNot recommended for ground installationNot good at curved surfacesNot good at special shapesNot good at wet areas

Description: The values in the table above are common ranges for various materials, used to illustrate applicable boundaries and not constituting a ranking of any material. For this project, coarse rammed earth flexible stone was ultimately selected because the New South Red rammed earth boards are laid throughout the entrance hall and main hall, in the same color family as the warm light of the lanterns.

2.0 Why Coarse rammed earth flexible stone

New South Red is a warm color leaning brick red, in the same color family as hot pot broth and lantern light. The rammed earth texture has light-dark transitions under angled spotlighting; layers can be seen up close, while from a distance it is a stable warm-colored surface. Hot pot restaurants mainly operate in the evening, and this color number produces the best effect under warm light.

2.1 Three questions for selection

Condense the selection into three questions, and the direction can basically be set:

  1. Is the wall curved or column-shaped? Yes → prioritize flexible materials that can bend; No → then compare weight and construction period.
  2. Can the substrate bear the weight of the stone? Cannot (lightweight partition walls, old walls, insulated walls) → prioritize flexible materials; can → natural stone is also an option.
  3. What kind of atmosphere does the space want? The condiment station and cashier counter background wall use the same material, with consistent color across areas.

The answers to the three questions for this project: New South Red rammed earth panels are laid throughout the entrance hall and main hall, in the same color family as the warm lantern light; the curved walls of the corridor and corners are fully wrapped in one piece, with seams continuing along the curves; and the condiment station and cashier counter background wall use the same material, ensuring consistent color across areas. Therefore, coarse rammed earth flexible stone was selected.

3. Configuration plan

3.1 Material specifications and packaging

Specifications (mm) Thickness (mm) Approx. weight per panel (kg) Wooden crate packaging (pieces/crate) Area of wooden crate after packaging (㎡) Weight after packaging approx. (kg)
600×12002.5–33–3.2300216820
1200×24002.5–312.5–131002881200

Optional colors: white, New South Red, Old South Red (other colors can be customized).

Texture and light perception notes: the layered feel of rammed earth texture comes from surface height differences, and angled lighting creates natural light-dark transitions.

3.2 Allocation by space

Different parts of the same project do not have the same requirements for materials. The table below breaks down the actual space of a Chinese-style hot pot restaurant and explains why each part is specified this way.

Space / Location Area share ★ Material usage Why set it this way?
Main viewing surface (the first wall directly facing you when entering)20% or soFull-piece laying, seams kept away from the centerWhere the line of sight rests longest, the overall appearance is most complete
Side walls and passagewaysabout 35%Conventional installation, with joints aligned continuouslyLarge area, with the focus on smooth, continuous seams
Curved wall / partitionabout 15%Full-piece curved wrappingPiecing curved surfaces into small pieces creates dense diagonal seams
Column wrappingabout 8%%Full-piece wrapping on the column surface, with seams kept at the sides and rearThe key is that no seams are visible from the front
Door openings and window casingsabout 10%Use matching termination pieces; do not butt-join on siteCut edges easily expose the panel backing
Form and local areasAbout 12%%Custom-shaped panels according to drawingsOn-site cutting precision for irregular pieces is insufficient

★Description: The proportions in the table above are common distributions for similar spaces and are used to estimate material quantities for each part; actual quantities are subject to on-site measurement and layout drawings.

3.3 Estimation of Quantity and Construction Schedule

The calculation process is given below so it can be reviewed according to your own project's basis.

Project Calculation formula Result
Net installation areaOn-site measurementApprox. 1050㎡
Material preparation area1050 × (1 + 12% loss)Approx. 1176㎡
Number of wooden crates1176 divided by 216 square meters per box, rounded upApprox. 6 boxes
Substrate treatmentLeveling, repair, primer2–3 working days
Layout setting-outSnap lines, align seams, set the starting point1-2 working days
Adhesive mounting4 people in a group, average daily 60–100 m² ★Approx. 15 working days
Finishing and acceptanceEdge trim, cleaning, acceptance1-2 working days
TotalConfigure for 4 people19 working days

3.4 Material List

Auxiliary materials Purpose Description
Special adhesiveMain material for full-surface bonding methodSelect according to product instructions; use weather-resistant type for outdoor or damp areas
Interface agentSubstrate sealingSelect according to substrate material
Edge trim / internal and external corner piecesCorners and closuresSame color family as the main material; prioritize matching accessories rather than on-site cutting
Joint filler materialJoint sealingClose to the main material color number to avoid overly prominent joint lines
DetergentCompletion cleaningNeutral cleaner; strong acids and alkalis prohibited

IV. Construction process and acceptance control points: on-site practice for "coarse rammed earth flexible stone"

4.1 Seven steps

  1. Substrate inspection: Moisture content, flatness, and strength must all pass. Flatness is checked with a 2 m straightedge; sanding and loose layers must be removed down to a solid substrate, and hollow areas must be knocked out and redone.
  2. Substrate treatment: Walls with high moisture content require a sealing primer first; different interface agents are selected for different substrates.
  3. Layout setting-out: Put the layout plan on paper before starting work; mark door and window openings, switches, sockets, and internal/external corner positions; align seam lines across different walls in the same space where possible.
  4. Cutting processing: Cut to layout dimensions; cover cut edges with trim or pressure strips; determine opening positions at the layout stage.
  5. Full bonding installation: The full-surface bonding method is recommended, starting from the main viewing face and progressing to both sides and upward; apply along the arc direction at curved areas.
  6. Finishing treatment: Internal and external corners use matching trim pieces; junctions with door frames, ceilings, and floors are executed according to the node drawings.
  7. Cleaning acceptance: Use a neutral cleaner to remove residual adhesive and fingerprints, and check item by item according to the acceptance checklist.

4.2 Acceptance Control Sheet

Inspection items Control points Criterion
Substrate flatness2 m straightedge inspectionGap not exceeding 3mm ★
Substrate moisture contentSeal damp areas firstNo obvious moisture marks, no water seepage
Joint line alignmentAlign joint lines within the same spaceSmooth and free of steps by visual inspection
Curved-surface installationDirection along the arcNo obvious sharp folds, no edge lifting
External corner closureUse matching termination piecesNo exposed board bottom, consistent color
HollowingSpot-check by tapping each pieceHollowing rate not exceeding 5% ★
Surface cleaningNeutral cleanerNo residual glue, no scratches

The specific allowable deviation values shall be subject to the standards and contract terms of the project location; the table above shows the common industry practice ranges.

4.3 Special methods for arc and column

Curved walls, columns and irregular corners are where flexible materials differ most directly from traditional finishes. There are several points that must be confirmed in advance for the installation method:

Location The method. Items to confirm in advance
Large-radius curved wall (R ≥ 2m)Full-piece curved application, seam following the curve directionArc radius, panel thickness, ambient temperature
Small-radius curved wall (R < 2m)Test the bend first; when there is obvious springback, switch to narrow-strip splicingMust first test bending with a physical mock-up
Cylindrical column claddingFull-piece wrapping, seam left at the side rearColumn diameter and whether there are embedded parts on the column surface
Arches and door openingsContinuous curve, use matching termination piecesDoor opening squareness
Internal and external cornersUse matching termination pieces; do not butt-join on siteWhether the color of finishing pieces is consistent with the main material

4.4 Common problems and avoidance

Phenomenon Reason Workaround
Joint misalignmentUneven substrate, cumulative error block by blockFirst snap lines to control continuous joints, and start installation from the main sightline
Curved-surface edge liftingRadius smaller than the material's usable rangeTest bending before installation to confirm; change to narrower strips if necessary
External corner showing through to the substrateOn-site cutting and butt-joiningUse matching inner and outer corner pieces
The light strip reveals the jointsJoint conflicts with the position of the light stripDetermine the joints together with the light strips during the layout stage
Color difference concentrationMixing different batchesOrder enough at once for the same batch, and mix materials before installation
HollowingBase-layer sanding and insufficient adhesive dosageSubstrate treatment in place, full-adhesion installation

4.5 Construction tools and personnel allocation

Project Configuration Description
Measuring tools2 m straightedge, level, tape measure, chalk lineBase-layer acceptance and chalk-line layout
Cutting toolsUtility knife / board cutting knife, straight rulerOn-site cutting according to layout dimensions
Mixing toolsElectric mixerMix the adhesive according to the specified ratio
Adhesive application toolsNotched trowelFull-surface bonding method: control consistent adhesive layer thickness
Compaction toolPressure roller / rubber malletRemove air bubbles and ensure full adhesion
Cleaning toolsSoft cloth, neutral cleanerCompletion cleaning
StaffingAdhesive mounting, 2–4 people per team ★This project is staffed with 4 people
Daily production capacity per group60–100 square meters per group ★Related to substrate conditions and modeling complexity

★Description: Staffing and daily capacity are common industry ranges, used to estimate the construction period; actual efficiency is affected by substrate conditions, shape complexity, floor height and on-site access conditions.

V. Image display and application description

5.1 Chinese dining area

Chinese-style dining area, warm red wall columns, wooden frame and red lanterns
Figure 1 · Chinese-style dining area, warm red wall columns, timber frame and red lanterns

5.2 End Scene Wall

End-view wall, warm red circular decoration and metal pendant light
Figure 2 · End wall, warm red circular decoration and metal pendant light

5.3 Corridor

Corridor: warm red wall with curved lighting decoration
Figure 3 · Corridor, warm red wall and curved lighting decoration

5.4 Passage Ceiling

Passage ceiling, warm red wall and suspended signage
Figure 4 · Passage ceiling, warm red wall and hanging signage

5.5 Entrance Corridor

Entrance passage, warm red wall with metal partition
Figure 5 · Entrance passage, warm red wall and metal partition

5.6 Corner End Scene

Wall corner end feature, warm red finish with three-dimensional decoration and plants
Figure 6 · Wall-corner vignette, warm red cladding with three-dimensional decor and plants

5.7 Arch Doorway

Arched door opening, warm red wall and bonsai
Figure 7 · Arched doorway, warm red wall and bonsai

5.8 Reception Area

Reception area, warm red background wall and wood-colored front desk
Figure 8 · Reception area, warm red backdrop wall and wood-colored front desk

VI. Communication and confirmation process

The following are several questions confirmed by both parties during material selection and construction, organized in the order of the conversation.

  • Design party: If the entire lobby wall is done in New South Red, will it be too red?
  • Our side: A single wall may look heavy on its own, but paired with a wood grille ceiling and dark flooring it is balanced. We suggest requesting a sample first and comparing it once under warm restaurant lighting.
  • Construction party: The corridor corner is curved—how do the panels transition?
  • Our side: Radii of 2 meters or more can be bent directly; for smaller corners, first take a sample and test bending, and confirm springback before ordering.
  • Owner: The wall behind the condiment station gets a lot of oil; is it easy to wipe clean?
  • Our side: The surface is dense; neutral cleaner with a soft cloth is enough. Do not use steel wool, as it will wear the texture flat.

Scope statement: The above is a written summary of the communication content, used to explain the decision-making process; it does not represent a commitment to results, and the contract terms and on-site conditions shall prevail.

Seven, usage effects and daily maintenance

7.1 Perception and light environment

The layered feel of the rammed earth texture comes from the height differences in the surface, and lighting at an angle creates natural light-dark transitions. The same wall looks different under different color temperatures: warmer under warm light and more neutral under cool light, which is also why we recommend sending physical samples first to compare under actual lighting.

7.2 Daily maintenance

Project The method. Note
Daily cleaningWipe with clean water or neutral detergentDo not use strong acids or strong alkalis
Oil stain treatmentNeutral cleaner + soft clothDo not use steel wool
Localized damageIndividual panels can be replacedReplaceable conditions were retained during layout
Damp areasMaintain ventilationDoes not absorb water, does not swell
Outdoor areasRegular washingExecute according to the design scope

7.3 Post-delivery Recheck Sheet

Review items Suggested timing Points of concern
Joints and closures7 days after handoverWhether there is lifting or cracking
Hollowing30 days after handoverSampling and tapping inspection
Color consistency30 days after handoverComparison across different walls and different areas
Cleaning statusDailyWhether there are stubborn stains

7.4 Intersection with Adjacent Materials

Wall materials rarely exist alone; there will always be neighbors such as ceilings, floors, wood veneer, metal parts and glass. How well the junctions are handled directly determines whether the elevation looks "clean" or "fragmented."

Adjacent materials Transition method Note
Ceiling / suspended ceilingPress the edge with a top trim strip, or leave a 3–5 mm revealJoint width must be consistent over the full length
Floor / skirtingSkirting line presses the lower edge of the panelDo not let the bottom edge sit directly on the floor, to avoid dragging wear
Wood finishTransition within the same color family, with the joint left at an internal cornerPlacing the two materials on the same wall requires comparing color differences first
Metal edge trim stripMetal strips press the seam, with the direction parallel to the grain directionColors are mainly matte dark tones to avoid stealing the show
Glass partitionUse a pressure strip for finishing, leaving a caulking gap between the glass and the panelCut edges of the panel need to be covered with trim
Door and window casingsUse matching termination pieces; do not butt-join on siteDoor opening squareness directly affects the finishing result

7.5 Cost Estimation

The cost of a wall consists of three parts: main material + auxiliary materials + labor. The budget estimate basis is as follows (◆budget estimate, not an actual measured bill):

Composition Scope Influencing factors
Main material.Material preparation area approximately 1176 ㎡ ÷ 216 ㎡ per crateColor, thickness, specifications, batch
Auxiliary materialsAdhesive + primer + trim pieces + groutSubstrate conditions, termination complexity
ManualMounting area × labor cost per unit areaForm complexity, floor height, proportion of special shapes

◆Estimate: Specific unit prices vary with pattern, thickness, order quantity, and construction conditions; a wide range is normal. This article does not provide a single quotation to avoid misleading; for project pricing, please provide the area, pattern, and delivery location.

VIII. Common questions (FAQ)

Below are the questions most frequently asked about material selection and construction in this project.

Is coarse rammed earth flexible stone suitable for spaces such as dining areas?

Suitable. The layered feel of the rammed earth texture comes from the surface height variation, and natural light-to-dark transitions appear when light strikes at an angle. This project uses it for the hot pot restaurant's entrance hall, lobby main wall and corridor walls. The New South Red rammed earth panels are laid throughout the entrance hall and lobby, in the same color family as the warm lantern light.

Can curved walls and column cladding be done in one continuous piece?

Yes. The material has a certain flexibility and can be bent within a certain radius, so columns, curved walls and irregular corners can achieve full-panel wrapping with continuous seams. The specific usable radius depends on the selected model, thickness and substrate conditions; it is recommended to first test-bend a physical sample at the corresponding curvature to confirm.

How long does the schedule generally take?

This project is about 1050 ㎡, with 4 workers, completed in 19 working days (including substrate treatment and edge finishing). The installation itself accounts for about 15 working days, with the rest for substrate, layout, and acceptance. The main variable in the schedule is the substrate condition—substrate rework will directly eat up the time saved by installation.

Can it be used in damp areas?

Yes. The material itself does not absorb water, and after construction the wall surface is not prone to dampness or mildew, so it can be used in humid environments and underground spaces. For wet areas such as bathrooms, it is recommended to confirm the specific scope in conjunction with the wet/dry zoning plan.

What about fire performance?

The material has flame-retardant properties; the specific combustion performance ratingshall be in accordance with the valid inspection report of the selected model. If the project has specific requirements for fire rating, please specify before placing an order.

How much difference in texture is there compared to natural stone?

Differences are visible up close: natural stone has naturally occurring random variation, while the texture of Coarse Rammed Earth flexible stone is formed by embossing or printing, giving greater consistency within the same product. From a distance the overall look is similar. When placing natural stone and flexible materials on adjacent walls in the same space, it is advisable to make a small sample comparison first.

Can old walls be renovated by direct pasting?

If the original wall surface is firm and has no hollowing, it is possible; old tile surfaces can also be covered directly. But before construction, each surface must be checked for hollowing, and hollowed areas must be knocked out and redone—this step cannot be skipped.

Does the material have test reports? What standard does it follow?

Execution JG/T 540-2017 'Building Flexible Stone-faced Decorative Material' (issued by the Ministry of Housing and Urban-Rural Development). Environmental protection and combustion performance test reports for the corresponding models can be provided with the goods.

How to confirm color and texture?

It is advisable to request physical samples and compare them under the project's actual lighting before deciding the color number. There are differences between screen display and actual materials; in particular, stone-texture materials look different at different angles and color temperatures.

Can a single damaged panel be replaced later?

Yes. During layout, the seam lines and termination positions have already been determined, and a single piece can be pried out from the termination for replacement. It is recommended to reserve 1–2 boxes of same-batch material as spares at delivery.

IX. Project File and Contact Information

Project Content
Project nameHot pot restaurant wall material recommendation - application case of New South Red rammed earth board flexible stone (Banan, Chongqing)
LocationBanan District, Chongqing
Main material.Coarse rammed earth flexible stone (Xinnanhong)
Material seriesRammed earth and cement series
Construction areaApprox. 1050㎡
Schedule19 working days
Related sectionsProject Cases · Food & Beverage Spaces
Implementation standardsJG/T 540-2017

Similar projects can be found in the Project Cases column; for material specifications and colors see Rammed earth and cement series.


Legend and specification notes

  • ★Project experience = Industry common practice and experience range, not a reference for national standard data.
  • ◆Estimate = Estimated value calculated based on the scale,not an actual measured bill; actual conditions are subject to the contract agreement and site conditions.
  • Material parameters are taken from the corresponding product file; combustion performance, environmental grade, etc. are subject to the valid test report for the selected model.
  • Area, schedule, and quantity are estimates based on industry-scale figures; the calculation process is provided and can be reviewed against your own project's basis.

Find the appropriate wall expression for your project.

Provide the type of space, wall area, and design intention. Communicate about materials, samples, and quotations.

Consulting project material selection ↗
Contact phone number Product Catalog Free Sample
WeChat ID copied